9 Common Blinds Installation and Removal Mistakes (And How to Avoid Them)

Published: 2026-07-08
By: Ray Moore
← Back to Blogs

Moving into a new rental or sprucing up your current one often means dealing with blinds. For renters, the stakes feel higher. Every hole, scratch, or misaligned bracket can chip away at your security deposit. I’ve installed and removed blinds in more Williamsburg apartments and homes than I can count, and I’ve seen the same mistakes play out again and again. The good news? Almost all of them are avoidable. Here are nine common blinds installation and removal mistakes—and how to steer clear of them.

The first mistake renters make is measuring incorrectly for inside mount blinds. An inside mount looks clean and built-in, but it demands precision. Measure the width at the top, middle, and bottom of the window frame. Use the narrowest measurement. If you assume the frame is perfectly square (and old Williamsburg homes rarely are), you’ll end up with a blind that either jams or lets in slivers of light. Outside mounts are more forgiving, but you need to account for extra width and height to block light fully. Measure twice, order once—it saves headaches.

Another common error is rushing the removal of old blinds. People yank them down, hoping for speed, and end up tearing the frame or pulling out chunks of drywall. Safe removal of old blinds protects frames and walls, which is everything when you’re a renter. Instead, take your time. Remove the valance first, then gently pry the brackets away from the frame with a flathead screwdriver. If the screws are painted over, score the paint with a utility knife before unscrewing. Patience here keeps your deposit intact.

Then there’s the dreaded patch job. After removing blinds, you’re left with small holes from brackets or screws. Ignoring them or slathering on spackle without sanding leaves a visible mess. Take the extra ten minutes to fill each hole, let it dry, and sand it smooth. A light coat of matching paint finishes the job. Landlords notice this kind of care. It also makes rehanging new blinds easier because the surface stays clean.

Aligning multiple blinds in the same room trips up even handy renters. If one blind sits a quarter-inch higher than the next, your eye catches it every time. Use a level and a chalk line to mark consistent heights before drilling. When installing brackets so blinds sit level and smooth, check both horizontally and vertically. A level bracket is non-negotiable. I’ve seen crooked blinds ruin the feel of a perfectly painted room. Take the time to get it straight.

People also forget to test the lift and tilt mechanisms before calling the job done. You install the blind, step back, and admire it—but the cord sticks or the slats don’t rotate evenly. Always raise and lower the blind fully, then tilt it open and shut. If something catches, adjust the bracket or the cord tension. This step takes two minutes and prevents frustration later. It’s the difference between a functional window treatment and a decorative annoyance.

A quieter mistake involves removing blinds for painting or replacement projects without labeling the hardware. You toss the brackets and screws into a bag, then can’t remember which screw goes where. Label each bracket with painter’s tape and a marker. Mark the top and bottom orientation. This small habit saves you from hunting for the right screw at the hardware store later.

Many renters also underestimate the quirks of Williamsburg homes. This town has centuries-old houses, converted duplexes near William & Mary, and newer apartment buildings with wiring that seems to follow no logic. I’ve drilled into a header only to hit an unexpected wire because the original builder ran it diagonally. For seniors renting condos or students in historic districts, the window frames may be warped or painted over so many times that the sashes stick. Hiring a professional who understands these nuances makes a real difference. That’s where a trusted local pro like Putivo comes in. We know which walls hide surprises and how to work with aged wood without cracking it.

Another frequent error is using the wrong hardware for the wall type. Drywall anchors work in modern apartments, but older Williamsburg homes often have plaster and lath. Plaster crumbles if you drill too aggressively. Use a masonry bit and toggle bolts for plaster walls. For lightweight blinds, adhesive strips can work, but they rarely hold up to daily use. Investing in proper anchors is worth it. If you search for a “blinds installer near me,” you want someone who knows the difference between drywall and plaster without guessing.

Finally, some people try to install blinds without checking the window’s true level. An old window might look straight but slope slightly. If you mount the bracket to the window frame itself, the blind will follow that slope. Instead, mount to the header or use shims to bring the bracket level. When you’re installing brackets so blinds sit level and smooth, a shim pack is your best friend. It compensates for the imperfections that give old homes their character.

If all this sounds like a lot, that’s because it is. Blinds installation and removal looks simple, but the details matter—especially when your deposit hangs in the balance. That’s why I built Putivo the way I did. We don’t rush. We measure, level, test, and clean up. We treat your rental like our own home.

My dad once told me, "You can't start a job and quit." He meant more than carpentry. He meant life. That mindset carried me through starting companies, moving across states, and now building Putivo. Whatever I start, I finish-and I finish it right.

Whether you need blinds removed before painting or a full set installed to make your space feel complete, knowing these mistakes helps you decide your next step. You can tackle it yourself with careful attention, or you can call a blinds installer near me who understands the nuances of Williamsburg homes. Either way, your windows—and your deposit—will thank you.